Loading... Please wait...
  • The Newborn LITE series is great for contractors take care of their gun and prefer to use a lighter bulk gun
  • Aluminum barrel, anodized blue and etched logo

Newborn LITE Aluminum 32 oz. Bulk Gun w/ Ring Cap

$56.75
SKU:
232-LITE
Weight:
4.00 LBS
Shipping:
Calculated at checkout
Quantity:

Product Description

Newborn  LITE 32 oz. Bulk Gun w/ Ring Cap    #232-LITE   -   70% lighter than the standard 232 model

 

Bulk / Sausage
Standard Square Rod

- 7:1 Thrust Ratio
- Lasts Longer - Heat Treated Rod Prevents Scoring
- Comes with More Accessories

 

Accessories Included:

- Leather Cups

- Floating Sausage Cup

- Ring Cap and 3  Cones

- OV-25 (1/2") Nozzle

- Bell Washer (Metal Conical Ejector)

- Leather Cup Spreaders (2)

- Replacement Parts Available

Product Videos

How To Use a Sausage Gun (12:32)
Website - www.NewbornCaulkGuns.com Facebook - www.Facebook.com/NewbornCaulkGuns CHECK OUT ALL THE COLORS AND DESIGNS! - http://newborncaulkguns.com/sites/default/files/Model%20620al%20colors%20sm_0.pdf How To Load The Sausage Gun With A Sausage Pack: 1. Hold the back handle, press the thumb release, and pull the rod all the way back. 2. Slide the sausage pack into the gun and bring it right up to the edge. 3. Slit the sausage pack around the crimp with the tip of a knife. 4. Use your knife to cut an opening in the cone with the angle and size you want to create. 5. Place the cone inside the end cap and screw the end cap on the gun. How To Change A Sausage Gun To A 10 Oz. Cartridge Gun: 1. Remove the barrel. 2. Loosen the set screw. 3. Remove the sausage only cup by hand. 4. Put the barrel back on. 5. Slide the 10 oz. cartridge into the barrel and screw the end cap back on. How To Change The Sausage Gun To A Bulk Gun: 1. Remove the barrel. 2. Loosen the top set screw and remove the sausage only cup by hand. 3. Take the dual hytrel cup-conical ejector combination and screw it on. Leave the set screw loose. 4. Put the barrel back on the gun. How To Use The Sausage Gun As A Bulk Gun (With A Follow Plate): 1. To open the metal bucket, use the pail lid opener to pry the tabs up. 2. Remove the plastic or any other sealant. 3. Push the follow plate down into the bucket until some material comes out of the center hole. 4. Place the sausage gun over the O-ring gasket. 5. Simultaneously push down on the back of the handle, pressing the thumb release down, while pulling back on the rod. 6. Remove the sausage gun from the bucket and place the end cap and cone on the front of the barrel. How To Use The Sausage Gun As A Bulk Gun (Without A Follow Plate): 1. To open the metal bucket, use the pail lid opener to pry the tabs up. 2. Remove the plastic or any other sealant. 3. Spray the front of the barrel with WD-40. 4. Push the rod all the way down. 5. Drop the front end of the gun into the material about an inch below the surface. 6. Move it around to make sure there are no air pockets. 7. Simultaneously push down on the back of the handle, pressing the thumb release down, while pulling back on the rod. Draw it up slowly and every so often, wiggle the gun to ensure that the barrel is below the surface. 8. Remove the gun from the material, clean off the barrel, and screw the end cap and cone on the front of the barrel.
  • How To Use a Sausage Gun
    Website - www.NewbornCaulkGuns.com Facebook - www.Facebook.com...
  • How To Use a Bulk Gun
    Website - www.NewbornCaulkGuns.com Facebook - www.Facebook.com...

Find Similar Products by Category




Categories

Sign up to our newsletter